EVS XT-3 Uživatelský manuál stáhnout pdf (Strana 103)

In standard configuration only Remote one (on RS422 port 1) is allowed to reset the

system.

Warning

This jumper should be removed if the device connected to the RS422 port is NOT

an EVS controller. Maximum voltage on pin 5 of an RS422 port of the server

should not exceed 5 Volt when the corresponding jumper is engaged. Applying a

higher voltage on pin 5 when the corresponding jumper is engaged will result in

permanent electronic damage to the board.

XT3 Server- Version 11.01- Hardware Technical Reference Manual

6. Boards Description 93

1 2 ... 98 99 100 101 102 103 104 105

Technical Reference 1
Hardware 1
Copyright 3
Disclaimer 3
Improvement Requests 3
Regional Contacts 3
User Manuals on EVS Website 3
Table of Contents 5
6. BOARDS DESCRIPTION 67 6
Table of Contents V 7
VI Table of Contents 8
What's New? 9
VIII What's New? 10
1.2. Proxy Server 12
2. Safety and Compliance 13
2.3. EMC Warning 14
2.4. FCCMarking 15
2.5. CE Marking 15
3. Hardware Specifications 16
3. Hardware Specifications 7 17
Dimensions 18
Top view 19
3.1.3. SAS-HDX Unit 20
3.1.4. Control Devices 21
3.2. Power Supply 22
3.3. Environmental Conditions 23
4. Software Specifications 24
SMPTE Standards 25
4.2. Audio Specifications 26
Audio Processing 27
4.3.1. Supported Codecs 28
4. Software Specifications 19 29
4.3.2. Maximum bitrates 30
4.3.3. Interpolation 30
2-Line Interpolator 31
4-Line Interpolator 31
4.4.1. Introduction 32
4.4.3. Choice of Bitrate 33
Motion 3x”) 34
Super Motion 3x”) 35
4.4.4. XF2 Transfers 36
4. Software Specifications 27 37
4.5. Recording Capacities 38
4. Software Specifications 29 39
30 4. Software Specifications 40
4. Software Specifications 31 41
32 4. Software Specifications 42
4. Software Specifications 33 43
34 4. Software Specifications 44
5.1. Rack Installation 45
5.2. Rear Panel Description 46
Video and Codecs 47
Analog and Digital Audio 47
RS422 Ports 48
Controls and Communications 49
Power Supplies 50
5.2.3. 4U Rear Panel Layout 51
Digital Audio 52
Analog Audio 53
5.3. Video Connections 55
5.4. Audio Connections 55
5.5. RS422 Connections 59
5.6. XNet Network 61
5.6.4. Starting XNet 65
5.7. Gigabit Network 66
5.7.2. Backup of Clips 67
5.7.3. Restore of Clips 68
5.7.4. Important Rules 69
5.7.5. Switches 69
Comparison 70
Additional Information 71
5.8. GPIOConnections 72
Specifications 73
TTL Inputs (GP In 5, 6, 7, 8) 74
5.8.3. GP Out Connections 75
6. Boards Description 77
6.2.1. Description 78
Block Diagram 79
Base Board Jumpers 80
Base Board LEDs 80
V3X COD Modules LEDs 81
Connector Assignments 82
6. Boards Description 73 83
74 6. Boards Description 84
76 6. Boards Description 86
Link 3G-SDI 87
78 6. Boards Description 88
80 6. Boards Description 90
6.2.6. Channel Assignment 91
2 Channels Server 92
6.3. Audio Codec Board 93
6.4. Raid Controller Boards 94
LEDs Function 95
Connectors 95
Gigabit Connectors 95
LEDs on Internal Array 96
6. Boards Description 87 97
LEDs on the External Array 98
Sound Alert on External Array 98
Disk Insertion and Removal 99
6.5. MTPC Board 100
6.5.2. A3/A6 Board 101
Multiviewer 102
LED Information 102
Board Configuration 102
6. Boards Description 93 103
94 6. Boards Description 104
+32 4 361 7000 105
+1 973 575 7811 105
+852 2914 2501 105

Komentáře k této Příručce

Žádné komentáře

EVS XT-3 Uživatelský manuál Strana 103

Komentáře k této Příručce

Související produkty a manuály pro Servery EVS XT-3